The PK-5 includes over 90 of our best shop tools selected with versatility in mind. A great way to outfit a pro bench or to set up a dream home workshop. The PK-5 is an impressive, professional set of specialty tools that can help you perform hundreds of bicycle repair and maintenance procedures. An investment you'll use and appreciate for decades. Kit Includes: - ATD-1.2 Adjustable Torque Driver - AWS-1 Three-Way Hex Wrench Set: 4, 5, 6mm - AWS-3 Three-Way Hex Wrench Set: 2, 2.5, 3mm - BBT-10.2 Adjusting Cap Tool: For 8-Spline Hollowtech II - BBT-22 Bottom Bracket Tool - BBT-69.2 Bottom Bracket Tool - BO-2 Bottle Opener - CBW-1 Open End Wrench: 8/10mm - CBW-4 Open End Wrench: 9/11mm - CC-4 Chain Checker - CN-10 Professional Cable and Housing Cutter - CNW-2 Chainring Nut Wrench - CP-1.2 Cassette Pliers - CT-3.3 Chain Tool - CWP-7 Compact Universal Crank Puller - DAG-2.2 Derailleur Hanger Alignment Gauge - DH-1 Dummy Hub - DP-2 Threaded Dummy Pedal - DSD-2 Derailleur Screwdriver: Cross Tip - DSD-4 Derailleur Screwdriver: Flat Blade - DT-2 Rotor Truing Fork - FR-5.2H Cassette Lockring Tool with Handle - GSC-1 GearClean Brush - HMR-8 8 oz. Shop Hammer - HXS-1.2 Hex Wrench Set - MLP-1.2 Master Link Pliers - NP-6 Needle Nose Pliers - PAW-6 6" Adjustable Wrench - PH-1.2 P-Handle Hex Wrench Set - PW-4 Professional Pedal Wrench - RR-12 Tape Measure - SBC-1 Spoke, Bearing and Cotter Gauge - SBS-1.2 Socket and Bit Set - SCW-13 13mm Shop Cone Wrench - SCW-14 14mm Shop Cone Wrench - SCW-15 15mm Shop Cone Wrench - SCW-16 16mm Shop Cone Wrench - SCW-17 17mm Shop Cone Wrench - SCW-18 18mm Shop Cone Wrench - SCW-19 19mm Shop Cone Wrench - SP-7 Side Cutter Pliers - SW-0 Precision Spoke Wrench: .127" - SW-2 Precision Spoke Wrench: .136" - SWR-8 3/8" Drive Ratchet Handle - SZR-1 Shop Scissors - TL-1.2 Tire Lever Set - TL-4.2 Tire Lever Set - TL-6.2 Steel Core Tire Levers - TWS-1 Torx Compatible Wrench Set - UP-SET Utility Pick Set - VC-1 Valve Core Tool - ZP-5 5" Flush Cut Pliers
The BBP-2 is a complete kit for replacing press fit bottom bracket bearings, cups, and adaptors. Includes a press assembly and compatible fittings for removing and installing most press fit bottom bracket configurations. The BBP-2 includes: - 6 sets of precision-machined bushings (in 9 sizes) to fit most bottom bracket configurations - 8 precision-machined extractor cups and 5 hardened collets for compatibility with most bearing IDs and bearing/cup ODs - 8 installation drifts for standalone bearing installation - Press assembly with comfortable handle, oversized shaft, and magnetic back plate for quick and easy assembly - Organized in two convenient storage cases The full list of bushing/collet/drift dimensions for bearing compatibility can be found on the instructions/parts diagram. NOTE: The BBP-2 consists of the BBP-1.2 Bottom Bracket Bearing Press Kit and BBP-AOS Bottom Bracket Bearing Extractor Add-On Set, both of which are available separately. However, the BBP-AOS requires the BBP-1.2 for use.
Proper frame preparation is very important. Park Tool's Head Tube Reaming and Facing Set combines reaming and facing of the head tube to create a perfect fit for most sizes of head cups. Includes: • 30.1 mm reamer (part #751.2) and four different size pilots (29.8mm, 30.0mm, 33.8mm, and 36.8mm) • 690 facer • Quick-release, quick-adjust feature: bottom portion slides off and on easily without threading SHIS terminology: The HTR-1 as stock will face frames of EC29, EC30, EC34 and EC37. It will ream frames of EC30. Accessories will allow service in other standards.
To ensure proper headset performance and longevity, special attention must be given to accurately machine the fork’s crown race seat. Park Tool's Crown Race Cutting Tool is a professional-quality machining tool for milling both the outer edge and lower surfaces of the crown race seat. • Includes high speed steel cutters and adjustable collets to machine 26.5mm and 27.1mm crown race seats on 1” forks and 30.1mm crown race seats on 1-1/8" forks • Unique adjusting system allows a tight fit of the tool on any fork, threaded or unthreaded (even forks with externally butted steerer tubes), ensuring a smooth, accurate cut and proper alignment of the fork in the frame • Cutter sized for 1-inch standard is part #845 (sold separately) • Cutter for 1-1/8 inch standard is #846 (sold separately)
The 16-piece set from the screwdriving tool specialist Wera solves the most important screwdriving problems associated with bicycles—reliable control of applied torque to protect sensitive components—with a click-torque wrench in the unmistakable Wera design. It features a very robust design with high accuracy, along with easy setting and saving of the default values. The audible and tactile snapping on reaching the scale values facilitates the safe setting of the desired torque values, while the robust release mechanism guarantees a clearly audible and tactile trigger signal when the set torque is reached - 16-piece wrench set for bicycle applications with torque control including Wera Clique-Torque wrench A 5 (2.5-25 Nm) - Sockets and bit sockets for the most popular screw profiles on road bikes, mountain bikes, and e-bikes - Easy setting and saving of the desired torque value with an audible and tactile click when the scale value is reached (click 1) - Safely quantified force: when the set value is reached, the torque wrench triggers audibly and noticeably (click 2) - Precise to +/- 4%
The BBP-AOS is used in conjunction with the BBP-1.2 Bottom Bracket Bearing Press Kit to extract press fit bottom bracket bearings, cups, and adaptors. The BBP-AOS utilizes an expanding collet and extractor cup system to safely remove bearings without requiring impact. Also included are eight installation drifts for pressing bearings into pre-installed cups. - 8 precision-machined extractor cups and 5 hardened collets for compatibility with most bearing IDs and bearing/cup ODs - 8 installation drifts for standalone bearing installation - Organized in a convenient storage case - Full list of compatible bearing inner/outer diameters found on instructions/parts diagram NOTE: The BBP-AOS requires the BBP-1.2 Bottom Bracket Bearing Press Set for use. The BBP-1.2 and BBP-AOS are also available as a complete set (part # BBP-2).
The Park Tool 758.2 will ream and face the head tubes of bike using the 1.5" standard. The 758.2 is designed for use with the Park Tool HTR-1 or HTR-1B Headtube Facer and Reamer. Must also be used with the 750.2 Centering Cone Adaptor.
Park Tool's Bottom Bracket Facing Set is designed to be a complete self-contained facing set, combining top-quality precision parts with ease of use. Simply install the threaded inserts using the facer handle, then insert the facing tool through the guides and install the tension spring and speed nut. After applying a liberal amount of cutting oil, the BFS-1 easily cuts the shell material, giving you a clean, faced surface. Now you're ready to install the bottom bracket. The English threading inserts are included. The Italian threading (36 x 24) inserts are available as an accessory, as part #688. Two are required.
Frame and Fork Taps will become a lifesaver at some time for virtually every mechanic. These taps are made of high-carbon steel and are precision ground. Park Tool's Frame and Fork Taps cut easily and fit conventional tap handles. - Tap-12.1: 12Mm X 1.0 - Tap-12.2: 12Mm X 1.5 - Tap-12.3: 12Mm X 1.75 - Tap-15.1: 15Mm X 1.0 - Tap-15.2: 15Mm X 1.5 - Tap-20.1: 20Mm X 1.0 - Tap-20.2: 20Mm X 1.5 - Tap-20.3: 20Mm X 2.0
High-quality combination ratchet wrench set by Wera. The new generation of combination ratchet wrenches, suitable for hexagon bolt heads or nuts. Comes with a holding function, thanks to the metal plate in the jaw, which reduces the risk of dropping nuts and bolts. - Practical holding function thanks to the metal plate in the jaw - Limit stop prevents any slipping - The double-hex geometry reduces the risk of slipping - Return angle of only 30 degrees - "Take-it-easy" tool finder: color coding by size
The 791 Reamer Set reamer is used on the PF30 frame shells. The reamer is sized at 45.94mm. The 791 Reamer Set must used with the HTR-1 Head Tube Reamer and Facer, a 750.2 Centering Cone and the 690-XL Facer. The 791 set also includes a pilot that allows a facing-only option of the PF30 frame shell.
ShockWiz is a suspension tuning system for air-sprung mountain bikes that combines high-tech hardware with an intuitive smartphone app. It's lightweight, durable and powered by a long-lasting coin cell battery, ShockWiz automatically records and evaluates suspension performance every time you ride. The ShockWiz app displays straightforward adjustments that unite bike, terrain and riding style. ShockWiz works for all mountain bike riders, regardless of their experience or bike's intended use. It works on hardtail and dual suspension bikes, and for all levels of skill, speed, and terrain. With ShockWiz, you know exactly how your suspension is performing – and how to make it better. Features & Benefits: - Automated tuning recommendations - Shock tuning score - a snapshot of how well your suspension is set up for you - Works on hardtail and dual suspension bikes. Works for Cross-Country, Trail, All Mountain and Downhill. - Inexpensive, replaceable CR2032 battery lasts for months - Waterproof and dustproof - IP67 rating - Two alternative hoses (included) offer a range of fitting options - Smartphone app is compatible with Apple and Android phones Essential Details: - ShockWiz is designed for all mountain bike riders, regardless of your experience or bike's intended use. - You can tune for every riding style: Efficient (pedaling), Balanced, Playful or Aggressive. - Advice for air pressure, spring rate, compression and rebound is displayed in the intuitive smartphone app. - In the box: ShockWiz hardware, two hoses, rubber mounting boot and zip ties.
Park Tool's 752 Reamer and Spacer Set allows reaming of bottom bracket frame shells in the BB30 standard. The reamer is sized at 41.94mm. It is used with the HTR-1 Head Tube Reamer and Facer and a 750.2 Centering Cone (each sold separately). The set includes a spacer to stop the reaming depth.
This Wheels Manufacturing Sealed Bearing Extractor Set removes sealed bearings with an inside diameter of 8mm to 30mm. Insert the extractor into the bearing, tighten one side with an Allen key, and the collet expands to grip the inside of the bearing. Tap the extractor out with a punch. - 12-piece set (Individual replacement extractors and parts are also available) - Made in the USA Set includes: - (1) Clear Plastic storage container - (1) 8mm ID Bearing Extractor - (1) 9mm ID Bearing Extractor - (1) 9.5mm ID Bearing Extractor - (1) 10mm ID Bearing Extractor - (1) 12mm ID Bearing Extractor - (1) 15mm ID Bearing Extractor - (1) 17mm ID Bearing Extractor - (1) 20mm ID Bearing Extractor - (1) 22mm ID Bearing Extractor - (1) 24mm ID Bearing Extractor - (1) 25mm ID Bearing Extractor - (1) 30mm ID Bearing Extractor - (1) Spare parts bag containing bolt sets for extractors
Portable bicycle pressure washer with three lances, custom waterproof bag, cleaning solution, Bike Protect, Drivetrain Cleaner and C3 Ceramic Lube. Water supply is required. - Includes 3 lances; 1 for bicycles, 1 for motorcycles (higher- pressure), 1 bespoke (adjustable higher presser) for heavy grime, custom waterproof dry bag carry case - Also includes snow foam lance for Muc-Off Nano Tech Bike Cleaner creating a thick snow foam for deep cleaning - Weight: 15lbs - Intended for use with cold water only
Park Tool's 692 Left-Hand Bottom Bracket Tap is a 1.370" x 24 TPI replacement tap for the BTS-1 Bottom Bracket Tap Set. This tap is used on the drive side (right side) of the bike. This side of the bottom bracket uses a counter-clockwise or left-hand thread. Note: It is very important to have sharp and accurate cutting tools for effective tapping and thread-chasing. Using an excessively worn or damaged tap can cause permanent damage to the frame and/or bottom bracket.
Park Tool's Right Hand Bottom Bracket Tap is a replacement tap for their BTS-1 Bottom Bracket Tap Set (sold separately). This tap is used on the non-drive or left side of the bike, which uses a clockwise or "right hand threading." Two taps are required for use.
We put together this set of carefully chosen tools to do basic maintenance and cleaning as well as perform a wide variety of repairs and adjustments on just about any bicycle. A perfect way to start or add to your collection of shop-quality bicycle tools. The AK-5 includes a tough toolbox to protect your investment. Kit Includes: - AWS-1 3-Way Hex Wrench - BBB-4 Big Blue Book of Bicycle Repair - CC-4 Chain Checker - CM-5.3 Cyclone Chain Scrubber - CN-10 Professional Cable and Housing Cutter - CNW-2 Chainring Nut Wrench - CT-3.3 Chain Tool - DCW-1 Double-Ended Cone Wrench: 13/14mm - DCW-2 Double-Ended Cone Wrench: 15/16mm - DCW-3 Double-Ended Cone Wrench: 17/18mm - DH-1 Dummy Hub - DT-2 Rotor Truing Fork - FR-5.2 Cassette Lockring Tool - GSC-1 GearClean Brush - HCW-16.3 Chain Whip/Pedal Wrench - HXS-1.2 Professional L-Shaped Hex Wrench Set - MLP-1.2 Master Link Pliers - PAW-12 12" Adjustable Wrench - RR-12 Tape Measure - SD-2 #2 Phillips Screwdriver - SD-3 3mm Flat Blade Screwdriver - SW-0 Precision Spoke Wrench: .127" - SW-2 Precision Spoke Wrench: .136" - TL-1.2 Tire Lever Set - TWS-3 Torx Compatible 3-Way Wrench - VC-1 Valve Core Tool
The BX-2.2 features updated pallet configuration and storage options to help you keep your tools secure and easily accessible. The expanded custom designed tool pallets, including dual-sided pallet wings, are all housed in a virtually indestructible composite travel case. Designed and built for the traveling mechanic who demands the best! - Custom designed tool-holding pallets with loops and pockets - Folding, dual-sided pallet wings - Front tool pallet that stores securely inside during transport - Dent-proof composite shell built around an aluminum frame - Key lock - Nominal dimensions: 19" x 14.85" x 8.5" (48.25 cm x 37.7 cm x 21.6 cm), 13.2 lbs. (6 kg)
Click-Torque wrench in the unmistakable, robust Wera design with high accuracy. Easy setting and saving of the default value. The audible and tactile clicks on reaching the scale values also facilitate the safe setting of the desired torque value. For right-hand use (clockwise torque control) and with 45-tooth reversible ratchet mechanism. - With 3/8" square drive, reversible ratchet, 45 teeth - Audible and tactile release mechanism when the set torque value is reached - Measuring range: 10-50 Nm; Precise to +/- 3% - Very robust design with ergonomic 2-component handle suitable for right-hand use
This is Wheels Manufacturing's new toolkit for installing, removing, and servicing Wheels Manufacturing bottom brackets. The kit includes their new bottom bracket socket tools for installing and removing Wheels Mfg. BB cups with the following spline patterns: 48.5mm 16-notch, 44mm 16-notch (may be compatible with FSA MegaEVO BB cups, Shimano, SRAM/Truvativ and FSA). It also includes sealed bearing extractors for 22mm, 24mm, and 30mm ID bearings. Includes - T-Handles with 1/2" threaded rod - (2) Universal bottom bracket drift (BB-OB) - (1) 48.5mm/44mm, 16-notch Bottom Bracket Socket - (1) 48.5mm, 16-notch Single Sided BB Socket - (1) 30mm ID sealed bearing extractor - (1) 24mm ID sealed bearing extractor - (1) 22mm ID sealed bearing extractor - (1) receiver cup - (1) 44mm receiver cup sleeve - (1) 42mm receiver cup sleeve - (1) 39mm receiver cup sleeve - (1) bearing pusher shaft - (1) 3/8" to 1/2" square drive adapter - Wood base
Click-Torque wrench in the unmistakable, robust Wera design with high accuracy. Easy setting and saving of the default value. The audible and tactile clicks on reaching the scale values also facilitate the safe setting of the desired torque value. For right-hand use (clockwise torque control) and with 45-tooth reversible ratchet mechanism. - With 1/4" square drive, reversible ratchet, 45 teeth - Easy setting and saving of the desired torque value with audible and tactile clicks when reaching the scale values - Audible and tactile release mechanism when the set torque value is reached - Measuring range: 2.5-25 Nm; Precise to +/- 4% - Designed with ergonomic 2-component handle suitable for right-hand use
- Precision tool for quickly and easily removing the headset crown race from the crown race seat of the fork - Fully adjustable, allowing precise, independent positioning of each blade around the crown race for flexibility in fitting around crown race interferences - Works with 1,1-1/8,1-1/4,1.5" forks (suspension or rigid) and crown races with outside diameters up to 64mm - Accepts steerers up to 430mm - All steel construction for long life
Park Tool's Fork Threading Set is designed for cutting new threads and for chasing existing threads on fork columns that are not chromed. The FTS-1's expandable cutting dies are made from the highest quality high-speed steel for precision cutting and long life. The unique thread guide system used with the FTS-1 is specially designed to allow the metal chips and shavings that result during use to fall completely through the guide, preventing damage to the fork threads and the tool. The FTS-1 includes: • Die handles • 1" x 24 tpi cutting die (Part #606) • 1" cutting guide (Part #610) Accessory dies and guides are also available separately: • 1-1/8" x 26 die (Part #607) • 1-1/8" guide (Part #611) • 1-1/4" x 26 die (Part #608) • 1-1/4" guide (Part #612) Die handles fit all three sizes of dies and guides.
Park Tool's Crown Race Cutter Adaptor is used in conjunction with the CRC-1 Crown Race Cutting Tool (sold separately) to machine 39.8mm crown race seats (1.5” standard) on tapered forks with 1-1/8” steerer tubes. It includes a precision-machined adaptor body and a 39.8mm high-speed steel crown race cutter. The CRC-15 will work on forks with a maximum 1.5-inch taper of 4.25 inches.
$188.21 - $239.25
Incredibly compact set arrangement with many tools in a minimum of space. A completely new ratchet set feeling thanks to the unique textile boxes that are very robust and durable. They can be positioned upright for tidy storage on the workshop shelf. Additional surface protection due to textile outer material. Low weight and volume for simpler mobility. - Freely pivoting ratchet head with 5 predefined locking positions - Fine toothing with 72 teeth - Small return angle of only 5 degrees - Free-turning sleeve for high working speeds - Take-it-easy tool finder: color coding by size
Another indispensable tool for the professional bike shop, the Wheels Manufacturing Press-2 works with bearings that have an I.D. of 10mm or smaller (most front hub sealed bearing fall in this range). It features an aluminum base with 9 open bore and over axle adapters, and a quick release skewer. - Installs sealed bearing sizes 6801, 6802, 6803, 6900, 6901, R6, 688, 608, 609 - All parts are laser etched for easy identification
$145.02 - $209.88
Park Tool has long provided some of the best cutting and machining tools in the bicycle industry. Their 690 Cutting Facers reflect their commitment to maintaining this high level of quality. Please read below for use and compatibility information specific to each size cutter: - 45mm (690): The 690 cutting facer is used on the HTR-1, HTR-1B, BFS-1, and BTS-1 cutting and facing tools. The facer has an outside diameter of approximately 45mm. - 57mm (690XL): The 690-XL is a larger version of the 690 facer for the HTR-1 Head Tube Reamer and Facer. It has a nominal outside diameter of 57mm. It may be used in conjunction with the 788 reamer. It is also used with the 767 Pilot or the 768 Pilot to face only the large diameter headtubes used with, "low profile," ZS-type headsets. - 65mm (690-XXL): The 690-XXL faces large headtubes. It has a nominal outside diameter of 65mm. Use the 690-XXL facer with the 750.2 Centering Cone Adaptor and 789 Reamer or 790 Pilot when facing head tubes with internal diameters of 55.95–55.90mm.
$120.52 - $202.18
Park Tool offers premium-quality reamers for nearly any bicycle standard. The reamers below are designed to quickly, accurately, and precisely ream headtubes when used with Park's Head Tube Reamer (HTR), ensuring a perfect headset fit and prfoessional-quality bicycle build. Choose the correct reamer for your application using the following information: - 751.2: This reamer is sized to 30.1mm. This allows a 0.1mm interference fit when pressing the 30.2mm headset of the “Euro” one-inch standard. - 754.2: This reamer is sized to 33.9mm. The allows a 0.1mm interference fit when pressing the 34.0mm headset of the 1-1/8" standard. - 788: This reamer is sized to 43.95mm. It reams head tubes to accept “internal” headset cups with 44.05 - 44.10mm O.D. (1-1/8 ZS standard). It is used with Park Tool's 690-XL Facing Cutter and 750 Centering Cone. - 738: This reamer is sized to 52.1mm. It is used to ream head tubes using the 1-1/2" integrated headset standard. It is used with Park Tool's 690-XL Facing Cutter and 750.2 Centering Cone Adapter. - 789: This reamer is sized to 55.95mm. It is used to ream head tubes to accept “internal” headset cups with 56.00–56.10mm O.D. (1-1/2 ZS standard). It is used with Park Tool's 690-XXL Facing Cutter and #750 Centering Cone Adaptor. - 799: This reamer is sized to 47mm. It is used for cutting the lower head tube on frames using an IS47 bearing for a 1-1/4" integrated headset. It cuts a 45-degree bearing set shoulder.
- Works in conjunction with Wheels Mfg sealed bearing press (BTI #WZ-9991) to install 10mm ID and larger bearings into hubs with shouldered axles, always pressing simultaneously on both the inner and outer race of the bearing and preventing damage during the installation process - Includes adapters for 12 different bearing sizes ranging from 10mm to 20mm: 6900,6000 (10mm ID); 6901,6001 (12mm ID); 6802,6902,6002 (15mm ID); 6803,6903,6003 (17mm ID); 6804,6904 (20mm ID) - Made in the USA
Page 1 of 17 Next page